Contact UsF111 EXTENSION HAND SPRAY GUNS
PRODUCT
-
F111-GXC
-
F111-GX
-
F111-SX
-
F111-PX
Features
HEAD ANGLE VARIABLE TYPE
|
The head angle can be adjusted 360°by simply loosening the base nut. Besides in head angle variable type, the head angle can be adjusted from 90° to -90° by loosening the top bolt. The dual pipe system employing separate pipes for the air and paint enhances compactness and durability. As the air circuit for spraying is not same as the one for spraying pattern, you can adjust the spraying pattern by hand. (Head angle variable type)
|
|
HEAD ANGLE FIXED TYPE
You can choose head angle 0° or 45°, and only head angle 45°
can be adjusted 360° by simply loosening the base nut.
Remarks |
| ●Head angle cannot be changed when the spray gun is in use, and shall be changed after cleaning the paint circuit with no fluids inside. Due to its design and structure, please avoid changing the angle frequently. ●When the spray gun is in use, please do not loosen the Air cap nut. When changing direction of Air cap, Air cap itself shall be turned without loosening the Air cap nut. ●Fluid viscosity shall be less than 30sec for Pressure type, and less than 20sec in case of Suction and Gravity type by using Meiji V-1 model viscosity cup. Fluids with high viscosity may result in less ejection amount and for PX17L, spray may not be in hollow cone. |
Specifications
| Model No. | F111-PXC10P <F111-PX10P> | F111-PXC13P <F111-PX13P> | F111-SXC15 <F111-SX15> | F111-GXC15 <F111-GX15> | |
|---|---|---|---|---|---|
| Type | Head angle variable type extension spray gun <Extension spray gun> |
||||
| Paint feed system | Pressure | Suction | Gravity | ||
| Nozzle bore |
mm (in) |
1.0 (0.039) |
1.3 (0.051) |
1.5 (0.059) |
|
| Spraying pressure |
MPa (PSI) |
0.25 (36) |
|||
| Air consumption |
L/min (cfm) |
170<180> (6.0 <6.4>) |
170<190> (6.0<6.7>) |
125<135> (4.4<4.8>) |
|
| Paint spraying volume | mL/min | 195<225> | 230<290> | 45<110> | 60<135> |
| Maximum effective pattern width |
mm (in) |
215<235> (8.465<9.252>) |
225<235> (8.858<9.252>) |
110<150> (4.330<5.906>) |
115<160> (4.528<6.299>) |
| Required compressor output | kW | 1.5 | 0.75 | ||
|
Head angle and inner dia. into which head can be inserted |
mm (in) |
0°:40 90°:60<0°:40 45°:55> (0°:1.575 90°:2.362<0°:1.575 45°:2.165>) |
|||
| Pipe length |
mm (in) |
500 1000*<500 1000 1500 1800*> (19.685 39.370*<19.685 39.370 59.055 70.866*>) |
500*<500*> (19.685*<19.685*>) |
||
| Weight |
g (lbs) [oz] |
625(Pipe length:500mm)<565(Pipe lenght:500mm)> (1.38(Pipe length:500mm)<1.25(Pipe lenght:500mm)>) [22.0(Pipe length:500mm)<19.9(Pipe lenght:500mm)>] |
|||
| Standard paint cup |
Paint pressure feed tanks, diaphragm paint pumps |
7SB, 7SLB | 2GA, 4GD, 4GB-U | ||
| ●Pipe length with mark * is the maximum length. Use of the longer pipe will result in reducing paint spraying volume. ●Paint viscosity should be 20 seconds for lacquer enamel using a Meiji mode V-1 viscosity cup, and the feed pressure for PX models should be 0.08MPa(12PSI). ●Nozzle bore of 0.8 mm(0.031in) and 1.5mm(0.059in) for PX type is available. Nozzle bore of 1.0mm, 1.3mm and 2.0mm for SX and GX types is available. |
|||||
3-14, 2-chome, Tagawa, Yodogawa-ku, Osaka, Japan